Painting Guides

Home/Painting Guides

LUXAPOOL Blisters & Craters in Epoxy Coating

The appearance of ‘blisters’ and resultant ‘craters’ may be experienced during, or shortly after, the application of certain epoxy coatings inclusive of LUXAPOOL EPOXY FINISH. WHEN ARE BLISTERS MOST OFTEN EXPERIENCED? The development of blisters will normally be limited to the warmer months, and more frequently experienced in tropical and subtropical zones. They will also [...]

2018-11-22T01:50:33+11:00June 20th, 2018|Commercial, FAQ, Painting Guides|

Concrete Cancer Repair

Overview: Concrete cancer may be experienced in older pools when concrete cracks, and water penetrates to the steel reinforcement deep inside the concrete. With emptying and refilling of swimming pools over time, and also thermal expansion and ground movement, minute cracks may occur in the concrete structure. The cracks then allow ingress of pool water [...]

2018-11-22T03:05:02+11:00June 20th, 2018|FAQ, Painting Guides|

LUXAPOOL Concentrated Wash

DESCRIPTION Luxapool concentrate wash is a non caustic amine detergent concentrate specially formulated for removing body oil and sunscreen residues prior to commencing any surface preparation for any Luxapool finish. APPLICATION Always add the detergent to warm water. 500mL will make up to 20L of wash solution and 5L will make up to 200L of [...]

2018-11-21T13:13:20+11:00June 20th, 2018|Painting Guides, Tech Data Sheets|

LUXAPOOL Epoxy Primer Sealer

LUXAPOOL Epoxy Primer Sealer is an integral part of the LUXAPOOL Epoxy Pool System where assurance of optimum adhesion is sought for many pool surfaces. Is a long proven solvent based, high solids, two part epoxy, designed specially to eliminate surface pin holes and the ingress of water soluble salts which could lead to the [...]

2018-11-22T02:26:05+11:00March 2nd, 2018|Painting Guides, Tech Data Sheets|

LUXAPOOL Epoxy Swimming Pool Coating

LUXAPOOL Epoxy Pool Coating is a long proven solvent based, high solids, two part epoxy, designed specially for use as a high performance swimming pool finish. Is suitable for most pool surfaces including new and aged render, marblesheen, fiberglass and existing epoxy finishes. It is suitable for both salt and chlorinated pools. Once cured, provides [...]

2018-11-22T00:12:50+11:00March 1st, 2018|Tech Data Sheets|

LUXAPOOL Chlorinated Rubber Pool Coating

POOLS PREVIOUSLY PAINTED WITH CHLORINATED RUBBER    SURFACE PREPARATION 1. Using a stiff brush or broom, scrub the entire surface with diluted LUXAPOOL Concentrated Wash (mixed at a ratio of 500mL Concentrated Wash to 20L of warm water). This removes greasy contaminants such as sun creams, oils, body fats, etc. Pay particular attention to step areas and [...]

LUXAPOOL Chlorinated Rubber

LUXAPOOL Chlorinated Rubber coatings are formulated specifically for application to new or old concrete, or previously painted chlorinated rubber finishes. They offer a cost effective, single pack, hard satin finish, with outstanding resistance to swimming pool chemicals and salt water. AREAS OF USE: The primary use of LUXAPOOL Chlorinated Rubber is water immersible applications such [...]

2020-06-05T12:30:48+10:00January 15th, 2018|Painting Guides, Tech Data Sheets|

LUXAPOOL SEF – Structural Epoxy Filler

Luxapool SEF is a specially formulated non-sag gap filling epoxy compound, ideal for swimming pool repair. This easy-to-use, two part, equal volume mix sets rapidly to a tough and chemical resistant final cure. Luxapool SEF adheres strongly to most surfaces including concrete, sound cement render, fibreglass, marblesheen, pebblecrete, stone and cleaned steel surfaces. It is [...]

2018-11-22T01:32:54+11:00January 15th, 2018|Tech Data Sheets|

LUXAPOOL Poolside & Paving

Description LUXAPOOL Poolside & Paving is an acrylic based, trafficable, rubberised, durable coating for exterior use especially in poolside areas. The resultant surface is naturally textured to provide a superior standard of non-slip, even under wet conditions. Textured effects may also be varied using special rollers in final application. In-film anti-mould ingredients provide long lasting [...]

2018-11-22T01:37:23+11:00January 15th, 2018|Painting Guides, Tech Data Sheets|

LUXAPOOL Epoxy Pool Coating – Pebblecrete Surface Pools

PEBBLECRETE SURFACE POOLS  SURFACE PREPARATION 1. Completely drain the pool so that all of the pebblecrete surface can be checked carefully for soundness. If there exists any evidence of loose pebbles or drummy areas, the surface should be regarded as suspect and must not be painted before being repaired. Loose or drummy areas of pebblecrete [...]