LUXAPOOL Poolside & Paving

Areas of Use

Pool surrounds and decks, disability ramps, pathways, outdoor living areas and boat decks.

Substrates

Suitable surfaces include new and old cement, masonry, fibreglass, pebblecrete and timber.

Features

• Water-based single pack acrylic coating with rubber crumb

• Safe P5 rated non-slip surface even under wet conditions

• Textured, elastic, seamless and waterproof

• Extremely durable, tough and trafficable

• UV resistant

• Resistant to algae, mould and fungal growth

• Easy clean up with water

• Low VOC

Properties

Finish:

Low sheen, textured

Weight Solids:

~66%

Volume Solids:

~58%

Theoretical Spreading Rate:

2 m2/L/coat

Wet Film Thickness:

500 µm WFT per coat (undiluted)

Dry Film Thickness:

290 µm DFT per coat

Specific Gravity:

1.33 kg/L

Chemical Resistance:

Unaffected by most mild acids, alkalis and bio deterioration

Odour:

Low

VOC:

18 g/L

The values listed are typical values and should not be interpreted as specifications.

Coverage

Apply a minimum of two coats in all applications. Additional coats will provide extended durability, texturing effect and water resistance, especially on high traffic surfaces.

Surface type and texture will affect the coverage rate. Typical application of 2 coats at a spreading rate of 2 m2/L per coat with a 10 mm nap roller, will yield an average DFT of 570–580 µm for two coats.

Precautions

Obtain a 7 day weather forecast.

Do NOT apply LUXAPOOL® Poolside & Paving:

1. If the surface or ambient temperature is above 35 °C or likely to be so during the drying period

2. If the ambient temperature is below 15 °C,

3. If the surface temperature is below 12 °C,

4. If minimum overnight temperatures are forecast to be below 12 °C within 7 days of application, or

5. In damp or rainy conditions, or when rain is forecast within 7 days

6. Avoid painting in direct sunlight on hot days

7. Do not apply in areas where extended ponding is likely to occur

All personnel participating in application must use appropriate personal protective equipment (PPE) to prevent contact with skin, eyes and breathing of vapours. A sun hat and sunscreen are also recommended if applying outdoors.

Application

Whilst the product is supplied ready for use, stirring prior to application is recommended to overcome any settling.

Preparation and application instructions can be found at luxapool.com.au

• New cement surfaces—refer to the

  Poolside & Paving NEW CEMENT SURFACES Application Guide

• Old cement surfaces—refer to the

  Poolside & Paving OLD CEMENT SURFACES Application Guide

• Masonry surfaces—refer to the

  Poolside & Paving MASONRY SURFACES Application Guide

• Pebblecrete surfaces—refer to the

  Poolside & Paving PEBBLECRETE Application Guide

• Fibreglass surfaces—refer to the

  Poolside & Paving FIBREGLASS SURFACES Application Guide

• Timber surfaces—refer to the

Poolside & Paving TIMBER SURFACES Application Guide

Scan for LUXAPOOL® Poolside & Paving Application Guides

Dry Times

Allow to dry for minimum 8 hours at 25 °C and 50% RH, or preferably overnight. Allow longer drying time in cooler and more humid conditions.

Hard Cure: 14 days (at 25°C and 50% R.H.)

*Best within 48 hours to minimise impact of airborne and other contaminants

Clean Up

Clean all equipment with water immediately after use and whilst still wet, away from drains and open watercourses. Dried material may be difficult to remove.

Colour range

Available in a range of 15 designer colours compatible with poolside and leisure use:

Arctic White Classic CreamTM Merino AS Y56

Beachsand (old Riversand) Arnhem

Surfmist® Shale GreyTM Dune® Winter Brown Basalt® Windspray®

Platinum Grey Deep Ocean® Monument® Night Sky®

COLORBOND® Steel colour names are registered trademarks of BlueScope Steel Ltd

Refer to colour card or website.

Packaging

Available in 15 L plastic re-sealable pails. Some colours are also available in 4 L. Reseal containers immediately after use.

Shelf Life

18 to 24 months if stored in a cool, dry place in unopened containers. Storage at high temperatures may reduce shelf-life.

Once opened and resealed, use the remaining contents within 3 months.

Health & Safety

This material is non-toxic and non-flammable. However, the contents should not be inhaled or ingested. Wear basic vapour masks and gloves when handling. Wash splashes on the skin with clean water. Clean all spills with absorbent material. Prevent washings from entering drains and waterways. Provide adequate ventilation if using in enclosed areas.

SDS available upon request.

Ancillary Products

Primer

Prior to applying LUXAPOOL® Poolside & Paving, unpainted surfaces will require priming.

Unpainted concrete, masonry, pebblecrete and fibreglass: ACRYLMERIC® Superseal Primer (solvent based option) or ACRYLMERIC® WB Epoxy Primer Membrane (water-based option)

Timber:

Colormaker Pink Wood Primer (solvent based)

Top coat

Application of a final coat of UNICRYL® HD Clear Glaze on top of LUXAPOOL® Poolside & Paving will enhance colour and gloss, provide increased resistance to staining and facilitate cleaning. However, this coating will also reduce anti-slip properties. For this reason a second coat of UNICRYL® HD Clear Glaze is not recommended on trafficable surfaces.